Do You Dilute Doterra Onguard Foaming Hand Wash?

No, you do not need to dilute Doterra Onguard Foaming Hand Wash. This product is safe to use as is and will not cause any irritation or skin problems.

Diluting Doterra Onguard Foaming Hand Wash is not necessary and may actually decrease the overall effectiveness of the product. The recommended usage is to dispense one pump into wet hands, lather thoroughly for 20 seconds, and rinse well with water.

Credit: www.doterra.com

How Do You Make on Guard Foaming Hand Wash?

One Guard Foaming Hand Wash is created with a special formula that allows for easy lathering and cleansing. The key ingredients in this product include: water, sodium laureth sulfate, cocamidopropyl betaine, glycerin, and disodium cocoamphodiacetate. To use, dispense a small amount into hands and rub together until lathered before rinsing clean.

How Do You Dilute Hand Soap for a Foaming Dispenser?

If you have a foaming hand soap dispenser, you might be wondering how to dilute the soap so that it works properly. Here are some simple instructions: 1. Start with clean water.

Fill the dispenser about three-quarters full with warm water. 2. Add liquid hand soap. Pour in a small amount of liquid hand soap, about 1/4 cup or less.

Use a mild soap since it will be diluted and will come into contact with your skin often. Avoid using antibacterial soaps or those with strong fragrances since they can be irritating when diluted. 3. Replace the Dispenser Pump Top and shake well.

Make sure the lid is on tight and then shake vigorously until the water and soap are combined and create foam. If there are still bubbles, add more soap a little at a time and shake again until desired consistency is reached.

Do You Need Water With Foaming Hand Wash?

One of the most common questions we get asked is whether you need water with foaming hand wash. The answer is no! Foaming hand wash is designed to be used without water, which makes it ideal for use in areas where water is not readily available.

All you need to do is pump a small amount of foam into your hands and rub them together until the foam lathers. Then simply rinse off the foam with clean water.

Is Foaming Hand Soap Just Diluted?

Foaming hand soap is not just diluted regular soap. The two products are actually quite different. Regular soap is made by combining oils or fats with an alkali, such as lye.

This process is called saponification and results in what we know as bar soap. Foaming hand soap, on the other hand, is made with surfactants. These are molecules that have one end that dissolves in water and another end that dissolves in oil.

When you add a surfactant to water, it reduces the surface tension between the two substances, which allows the water to more easily penetrate dirt and grime. Soap also contains air bubbles, which help to lift dirt and grime from surfaces. However, these bubbles are relatively small and quickly pop due to the weight of the water they contain.

Foaming hand soap contains larger bubbles that are filled with less water and thus last longer before popping. This allows you to scrub your hands for a longer period of time without losing any of the cleaning power of regular soap.

OnGuard Foaming Hand Wash Tip

Doterra Foaming Hand Wash Dilute

5 tsp. doTERRA essential oil with 1 cup water in a foaming soap dispenser. If you’re looking for an alternative to conventional hand soaps, consider using doTERRA essential oils to make your own foaming hand wash!

All you need is a foaming soap dispenser and some water; add in half a teaspoon of your chosen oil (or blend of oils) and give it a good shake. The doTERRA website has some great recipes for different scents, or you can experiment on your own – just remember that less is more when it comes to essentials oils, so start small and build up as needed.

Conclusion

If you’re using Doterra’s On Guard Foaming Hand Wash, you may be wondering if you need to dilute it. The answer is no! This hand wash is already diluted and ready to use.